Compression test
Last Updated on July 22, 2024 by Mutiara
The 1.6 L 3 cylinder turbocharged EcoBoost engine is an upcoming design in a number of Ford vehicles wearing the Read more
Common Ford power steering issues Ford power steering pump with reservoir. The power steering system commonly found on most Ford Read more
The Ford MTX-75 (Manual TransaXle), is a 5-speed transmission developed by Ford Motor Company for its larger engined front wheel drive models. "75" refers to Read more
This page contains some modifications that were done to a Ford Windstar with a 3.8 Ford Essex engine for amusement. Read more
LS9 Cutaway, revealing the valves and piston.
Since the essential function of an engine is pumping air, it is crucial to have good compression. Testing the compression of an engine is a good way to tell if it is healthy. If an engine has poor compression it will run inefficiently (if it runs at all), rough, and have issues starting.
Generally most piston driven gasoline engines should have 120 to 160 lb. of cranking compression with no more than 10% difference between the cylinders. Although due to variances in engine design, the exact range should be looked up or calculated for the specific engine.
How to check compression
Average compression tool set.
Checking the compression manually with a gauge is a fairly simple procedure. It requires removing all the spark plugs, unplugging the ignition coil, and holding open the throttle. With the hose from the gauge threaded into the spark plug hole, the engine should be cranked and then the pressure noted.
The 1.6 L 3 cylinder turbocharged EcoBoost engine is an upcoming design in a number of Ford vehicles wearing the Read more
Common Ford power steering issues Ford power steering pump with reservoir. The power steering system commonly found on most Ford Read more
The Ford MTX-75 (Manual TransaXle), is a 5-speed transmission developed by Ford Motor Company for its larger engined front wheel drive models. "75" refers to Read more
This page contains some modifications that were done to a Ford Windstar with a 3.8 Ford Essex engine for amusement. Read more
While unplugging the ignition coil is the most popular and simple way to do a compression test, it is recommended to kill the fuel system as well to ensure more accurate readings. The fuel injected each time the engine is cranked is washing down the bores, which can make the compression readings abnormally decrease from the first to the last cylinder tested. This can be done numerous ways such as initiating the fuel cutoff switch or removing the fuel pump fuse while the car is running to ensure no pressure is left in the fuel rail, or unplugging fuel injectors to prevent them from spraying.
Some older cheap gauges will require having an assistant to look at the gauge and note the pressure. However most decent compression gauges come with a one way valve that allows you to capture the reading and then release the pressure manually.
Determining the source of low compression
Testing the compression of an engine is a great method to diagnosing the problem in an engine without having to go through dis-assembly.
- Low compression in one cylinder is caused by a leaking exhaust or intake valve, typically caused by pitting on the mating surfaces and requires replacement or lapping of the valve.
- Low compression in two adjacent cylinders is caused by a blown head gasket, typically as a result of being crushed from heat expansion.
- Low compression in all cylinders is a good indicator that the cylinders and rings are worn out and require an engine overhaul.
- Squirting a small amount of motor oil into the cylinder through spark plug holes and repeating the test can help determine if the compression loss is due to leaking valves or piston rings. If it is the rings or cylinder walls, the oil will temporarily seal them and give quite a higher reading during a second test.
The 1.6 L 3 cylinder turbocharged EcoBoost engine is an upcoming design in a number of Ford vehicles wearing the Read more
Common Ford power steering issues Ford power steering pump with reservoir. The power steering system commonly found on most Ford Read more
The Ford MTX-75 (Manual TransaXle), is a 5-speed transmission developed by Ford Motor Company for its larger engined front wheel drive models. "75" refers to Read more
This page contains some modifications that were done to a Ford Windstar with a 3.8 Ford Essex engine for amusement. Read more
